Latest Network Appliance NS0-014 First Attempt, Exam real Dumps Updated [Apr-2026]
Get the superior quality NS0-014 Dumps Questions from Actual4Dumps. Nobody can stop you from getting to your dreams now. Your bright future is just a click away!
NEW QUESTION # 13
Which component does the MetroCluster Tiebreaker software primarily interact with to monitor cluster health?
- A. IP switches
- B. Data ONTAP Mediator
- C. SyncMirror
- D. FC switches
Answer: B
NEW QUESTION # 14
Which MetroCluster components require configuration for both FC and IP configurations? (Select two)
- A. Tiebreaker software
- B. IP switches
- C. ATTO bridges
- D. WAN connections
Answer: A,D
NEW QUESTION # 15
Which tool confirms compatibility between a fabric-attached MetroCluster ONTAP software release and an FC switch firmware release?
- A. Active IQ Unified Manager
- B. ONTAP Mediator
- C. MetroCluster Tiebreaker software
- D. Active IQ Config Advisor
Answer: D
NEW QUESTION # 16
In a MetroCluster environment, which two steps are required to configure FC switches? (Select two)
- A. Configure VSANs for all switches
- B. Configure IPsec for secure communication
- C. Set up inter-switch links (ISLs) between the FC switches
- D. Enable NPIV (N-Port ID Virtualization)
Answer: C,D
NEW QUESTION # 17
What is the main function of the metrocluster check command in ONTAP?
- A. To force a site switchover
- B. To perform a complete configuration backup
- C. To verify that MetroCluster components are functioning properly
- D. To initiate a storage failover
Answer: C
NEW QUESTION # 18
When expanding a MetroCluster configuration, what must be considered regarding inter-site connectivity?
- A. Network bandwidth and latency between sites
- B. The number of controller nodes
- C. The number of users accessing the system
- D. The cooling system efficiency
Answer: A
NEW QUESTION # 19
What does the MetroCluster Tiebreaker monitor to determine if a failover should occur?
- A. Inter-site latency
- B. Site availability
- C. Data replication status
- D. Mediator heartbeat
Answer: B
NEW QUESTION # 20
What is the first step when installing a MetroCluster configuration?
- A. Validate hardware and site readiness
- B. Install the ONTAP Mediator
- C. Set up the SyncMirror configuration
- D. Install the ATTO bridges
Answer: A
NEW QUESTION # 21
When troubleshooting a site failure in MetroCluster, which log file provides detailed information about the failure event?
- A. Tiebreaker log
- B. SyncMirror log
- C. ONTAP Syslog
- D. Cluster log
Answer: A
NEW QUESTION # 22
What is a key advantage of IP MetroCluster over Fibre Channel MetroCluster?
- A. Increased storage capacity
- B. Easier setup and longer distance replication
- C. Lower bandwidth requirements
- D. Higher performance
Answer: B
NEW QUESTION # 23
A customer is using MetroCluster Tiebreaker software with Observer mode set to true. Tiebreaker just confirmed a disaster at one site. Which two steps must you perform to recover the service?
(Choose two.)
- A. Execute the metrocluster configuration-settings -switchover true command on the disaster site.
- B. Verify that the disaster site is down.
- C. Open a case with the NetApp Support Site before executing any command on the system.
- D. Execute the metrocluster switchover-forced-on-disaster true command on the surviving site.
Answer: B,D
NEW QUESTION # 24
What is the requirement when installing ONTAP Mediator for a MetroCluster over IP configuration?
- A. It must be installed at a separate location from the MetroCluster sites.
- B. It must be deployed behind a firewall.
- C. It must be installed on a physical host.
- D. It must be installed at a cloud provider that is ISO 27001 certified.
Answer: A
NEW QUESTION # 25
Which switch configuration is necessary for the communication between MetroCluster nodes?
- A. Fibre Channel over Ethernet (FCoE) switches
- B. FC switches with ISL links
- C. IP-based switches with cross-links
- D. Ethernet switches in loop mode
Answer: B
NEW QUESTION # 26
Which two configuration steps are essential when installing MetroCluster Tiebreaker software?
(Select two)
- A. Install ONTAP Mediator
- B. Enable SyncMirror
- C. Configure cross-site LIFs
- D. Set up IP connectivity between clusters
Answer: C,D
NEW QUESTION # 27
Which ONTAP tool should be used to validate the MetroCluster configuration and perform health checks?
- A. ONTAP Mediator
- B. Config Advisor
- C. OnCommand Unified Manager
- D. System Manager
Answer: B
NEW QUESTION # 28
......
Network Appliance Practice Test Engine with NS0-014 Questions: https://drive.google.com/open?id=1DJC8_w1BV7qLQxj1gW2Ys77VkRMiPZ9f
Guaranteed Success with Valid Network Appliance NS0-014 Dumps: https://www.actual4dumps.com/NS0-014-study-material.html