Verified D-PST-DY-23 Q&As - Pass Guarantee D-PST-DY-23 Exam Dumps
Check the Free demo of our D-PST-DY-23 Exam Dumps with 220 Questions
NEW QUESTION # 10
SIMULATION
A storage admin is setting up a new protection policy with only snapshot rule for a new file system in PowerStore.
The administrator is given the below parameters.
Use the simulator to perform the configuration task.
When you have finished continue to the next question.
Answer:
Explanation:
See explanation below
Explanation:
1. Create the File System
Navigate to Storage > File Systems.
Click Add File System.
Enter the file system name: FS-1
Set the file system size to 5 TB.
Select the appropriate NAS Server (SMB-NAS Server in this case).
Click Add.
2. Create the Protection Policy
Navigate to Protection > Protection Policies.
Click Add Protection Policy.
Enter the policy name: Policy-1
Click Next.
3. Configure the Snapshot Rule
In the "Snapshot Rules" section, click Add Rule.
Enter a name for the rule (e.g., "Snap-Rule").
Set the Days to Tuesday.
Set the Every field to 1 Hour.
Ensure that Retention is set to the default value.
Click Add.
Click Next.
4. Review and Finish
Review the protection policy summary.
Click Finish.
5. Apply the Protection Policy to the File System
Navigate back to Storage > File Systems.
Locate the FS-1 file system.
Click the More Actions button (three vertical dots) and select Edit.
In the "Protection Policy" field, select the newly created Policy-1 from the dropdown list.
Click Save.
Verification
To verify the configuration, go to Protection > Protection Policies.
Select Policy-1.
You should see the configured snapshot rule ("Snap-Rule") with the specified settings.
Key Considerations
Default Retention: The default retention for snapshots in PowerStore will vary depending on your system configuration. Ensure that the default retention meets your data protection needs.
Snapshot Schedule: The snapshot rule you created will take hourly snapshots of the file system every Tuesday.
By following these steps, you'll successfully create the protection policy with the specified snapshot rule and apply it to the new file system, meeting all the requirements of the simulation task.
NEW QUESTION # 11 
An administrator is setting up a new ESXi cluster using NVMe over TCP. The administrator is given the following parameters:
Volume Details
Name: nvme-ds-01
Category: Virtualization
Application: Containers/Kubernetes
Volume Performance Policy: High
Size: 2 TB
Host Details
Name: ESXi-01
Initiator Type: NVMe
Host Mappings: NVMe
Use the simulator to add the host and the volume and give the host access to the volume using the above parameters.
When you have finished, continue to the next question.
Answer:
Explanation:
See the steps in Explanation.
Explanation:
1. On the simulator, click on theStoragetab on the left sidebar. Then click on theVolumessubtab. You will see a list of existing volumes on the cluster.
2. To create a new volume, click on theCreatebutton on the top right corner. A dialog box will appear where you can enter the volume details.
3. Enter the name of the volume asnvme-ds-01. Select the category asVirtualizationand the application asContainers/Kubernetes. These are optional fields that help you organize and identify your volumes.
4. Select the volume performance policy asHigh. This will optimize the volume for high performance and low latency. You can also customize the policy by clicking on theAdvancedbutton and adjusting the settings.
5. Enter the size of the volume as2 TB. You can also enable thin provisioning, compression, and deduplication if you want to save space and improve efficiency. Click on theCreatebutton to create the volume.
6. You will see a confirmation message that the volume has been created successfully. Click on theClosebutton to exit the dialog box. You will see the new volume in the list of volumes.
7. To add a new host, click on theHostssubtab on the left sidebar. You will see a list of existing hosts on the cluster.
8. To create a new host, click on theCreatebutton on the top right corner. A dialog box will appear where you can enter the host details.
9. Enter the name of the host asESXi-01. Select the initiator type asNVMe. This will enable the host to use the NVMe over TCP protocol to access the volumes.
10. To add the host mappings, click on theAdd Mappingbutton. A dialog box will appear where you can select the volume and the access type.
11. Select the volumenvme-ds-01from the drop-down menu. Select the access type asNVMe. This will map the volume to the host using the NVMe over TCP protocol. Click on theAddbutton to add the mapping.
12. You will see the mapping in the list of host mappings. You can add more mappings if you want to map more volumes to the host. Click on theCreatebutton to create the host.
13. You will see a confirmation message that the host has been created successfully. Click on theClosebutton to exit the dialog box. You will see the new host in the list of hosts.
14. You have completed the task of adding the host and the volume and giving the host access to the volume using the NVMe over TCP protocol. You can verify the configuration by clicking on the host or the volume and checking the details.
NEW QUESTION # 12
What is the default replication interface assigned after initial configuration of a PowerStore 5000T system?
- A. 4PortCard-FEPort1
- B. 4PortCard-FEPort0
- C. 10 GbE Optical Port-0 in IOModule-0
- D. LACP bond
Answer: D
NEW QUESTION # 13
What does a Storage Administrator need to consider about Resource Balance when assigning volumes?
- A. Whether the appliance is offline
Appliance failure status
Capacity utilization - B. Whether the Node is offline
Appliance failure status
Node utilization - C. Whether the Cluster is offline
Node failure status
I/O utilization - D. Whether the appliance is online
Appliance failure status
Cluster utilization
Answer: A
NEW QUESTION # 14
What establishes a data path between the ESXi hosts and the PowerStore storage container having vVols?
- A. VASA Protocol
- B. Protocol Endpoints
- C. VASA Provider
- D. NFSv4 Protocol
Answer: B
NEW QUESTION # 15
A PowerStore Administrator was tasked with provisioning block storage to hosts using iSCSI initiators. The Administrator configured iSCSI Auto Discovery IP address, but the iSCSI initiators are NOT automatically discovered in PowerStore Manager.
What is the issue?
- A. IQN Auto Discovery is not enabled on the PowerStore cluster
- B. An iSCSI embedded module is connected to the cluster
- C. CHAP authentication is disabled
- D. CHAP authentication is enabled
Answer: D
NEW QUESTION # 16
Which two statements are true regarding host group configurations? (Choose two.)
- A. Maps volumes to all hosts in the host group.
- B. Allows mapping volumes to individual hosts in the host group.
- C. Volume-related operations are made across all hosts in the group.
- D. Allows mixed protocol type hosts within the same host group.
Answer: A,C
NEW QUESTION # 17
A storage administrator has provisioned 10 × 2GB volumes. 400MB of data is written to each of the ten volumes.
What is the Thin Savings ratio for this configuration?
- A. 5:1
- B. 3:1
- C. 4:1
- D. 6:1
Answer: A
NEW QUESTION # 18
Place the steps in the correct order to map a PowerStore volume to a NVMe host.
Answer:
Explanation:
1 - add NVMe over TCP Sofware Adapter
2 - Add Host
3 - Add Controller
4 - Add NVMe volume
NEW QUESTION # 19
A storage administrator has provisioned a 50GB volume and presented it to an application. The application owner has requested that the volume be replicated to a secondary array.
Which policy should be assigned to the volume to enable replication?
- A. Performance
- B. Replication
- C. Protection
- D. Remote
Answer: C
NEW QUESTION # 20
Which configuration item is optional during the PowerStore ICW?
- A. Support and CloudlQ
- B. Default Users
- C. Management Network
- D. Fault Tolerance
Answer: A
Explanation:
Core service components that are required to be initialized are Telemetry Notice, Cluster Details, Default Users, Fault Tolerance, Management Network, Infrastructure Services, and Create Cluster. As a result of successful core initialization steps, a cluster is created, but not fully configured. (P59 of POWERSTORE 3.0 POWERSTORE T IMPLEMENTATION)
NEW QUESTION # 21
A Customer creates a new volume and maps this volume to an ESXi host. The Customer opens the vCenter Server and after browsing the datastores the new volume does not appear.
What is the first operation a customer should carry out to see the newly created volume?
- A. Rescan Storage from the vCenter Server
- B. Set the volume Performance Policy to High
- C. Create a datastore on the vCenter Server
- D. Set the volume Logical Unit Number to 0
Answer: A
NEW QUESTION # 22
Which storage protocol is commonly used for block-level access in PowerStore environments?
- A. NFS (Network File System)
- B. HTTP (Hypertext Transfer Protocol)
- C. SMB (Server Message Block)
- D. iSCSI (Internet Small Computer System Interface)
Answer: D
NEW QUESTION # 23
A customer is new to PowerStore and asks if there are any differences between the A and B back-end ports.
What is the correct response?
- A. All ports on the base enclosure are output ports
- B. "A" ports are output ports and "B" ports are input ports
- C. All ports on the base enclosure are input ports
- D. "A" ports are input ports and "B" ports are output ports
Answer: B
NEW QUESTION # 24
Refer to the Exhibit.
A Network administrator is failing to discover a PowerStore T system using the PowerStore Discovery Utility.
What might be the issue?
- A. Dedicated port needs to be used for discovery network
- B. Port 54 has not been set to trunk mode
- C. Port 54 needs to be enabled
- D. Discovery network uses only native VLAN
Answer: D
NEW QUESTION # 25
What is the final configuration step when installing the ImportKit for a Windows host accessing VNX2 storage?
- A. Select the RSA key for configuring the control path HTTPS certificate
- B. Configure the network port and interface for the host data path
- C. Configure the network port and interface for the management control path
- D. Select the folder location on the host for the program installation
Answer: C
NEW QUESTION # 26
An administrator is attempting to create a protection policy while creating an SMB share however the option is not available.
What is the reason?
- A. The protection policy has been previously associated with a file system
- B. The protection policy is only available with file level retention enabled
- C. The protection policy must be created before associating it with the file system
- D. The protection policy must be created before associating it with the volume resource
Answer: C
NEW QUESTION # 27
The wan connection between the production and DR sites has a low latency of <5 milliseconds.
Which firewall port is used by PowerStore to communicate between sites?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
PowerStore uses port 13337 for communication between sites in a replication setup. This port is required to enable data transfer and management communication over the WAN connection between the production and disaster recovery (DR) sites. The low latency condition (≥ 120 milliseconds) highlights the importance of maintaining efficient data transfer, and proper firewall configuration ensures PowerStore uses different ports for replication traffic based on the latency between the two sites. Since you have a low latency connection (< 5 milliseconds), PowerStore will use port 13333.
Here's a breakdown of the ports and their corresponding latency:
13333: Low latency (< 5 milliseconds) - This is the default setting.
13334: Low Medium latency (>= 5 and < 20 milliseconds) 1
13335: Medium latency (>= 20 and < 60 milliseconds)
13336: Medium High latency (>= 60 and < 120 milliseconds)
13337: High latency (>= 120 milliseconds)
It's important to configure your firewalls to allow traffic on the correct port to ensure successful replication between your production and DR sites.
NEW QUESTION # 28
What describes the remote replication Failover operation?
- A. It is run from the replication source system by the administrator in the event of an outage on the system
- B. It is run automatically by the replication source system in the event of a source system outage
- C. It is run from the replication destination system by the administrator in the event of a source system outage
- D. It is run automatically by the replication destination system in the event of a source system outage
Answer: C
NEW QUESTION # 29
A SQL Cluster with attached PowerStore storage has Volumes SQL1, SQL2, SQL4, SQL5 which all require write order preservation. The SQL administrator no longer requires SQL4 and has removed it from the database. The Storage Administrator goes to delete volume SQL4 and finds that the option is grayed out.
Why is the option to delete the volume unavailable?
- A. SQL4 still has replications
- B. SQL4 is part of a volume group
- C. SQL4 still has snapshots
- D. SQL4 was renamed from SQL3
Answer: B
NEW QUESTION # 30
......
Get professional help from our D-PST-DY-23 Dumps PDF: https://www.actual4dumps.com/D-PST-DY-23-study-material.html
Clear your concepts with D-PST-DY-23 Questions Before Attempting Real exam: https://drive.google.com/open?id=1AijWy5CE960xq_b19-x3JXU0gttpWURv