HPE6-A73 Practice Exam Tests Latest Updated on Dec-2021
Pass HPE6-A73 Exam in First Attempt Guaranteed Dumps!
What is the cost of Hewlett Packard Enterprise Aruba Certified Switching Professional Exam
The cost of Hewlett Packard Enterprise Aruba Certified Switching Professional Examis $300.
- Format: Multiple choices, various answers
- Length of Examination: 140 minutes
- Number of Questions: 120
NEW QUESTION 37
Examine the network topology.
Company XYZ has two connections to a service provider (ISP1). Here is the configuration of Router1:
Here is the configuration of Router2:
Based on configuration of Router1 and Router2, which BGP metric is being manipulated?
- A. Multiple exit discriminator
- B. Weight
- C. AS path length
- D. Local preference
Answer: A
NEW QUESTION 38
An administrator is defining a VSX LAG on a pair of AOS-CX switches that are defined as primary and secondary. The VSX LAG fails to establish successfully with a remote switch; however, after verification, the remote switch is configured correctly. The administrator narrows down the problem to the configuration on the AOS-CX switches.
What would cause this problem?
- A. LACP was enabled in active mode on the VSX LAG
- B. The VSX LAG hash does not match the remote peer
- C. Local optimization was not enabled on the VSX LAG
- D. The VSX LAG interfaces are in layer-3 mode
Answer: B
NEW QUESTION 39
Examine the AOS-CS switch output:
Based on this output, what is correct?
- A. 802.1X authentication was successful, but MAC authentication is yet to start
- B. 802.1X authentication occurred and downloadable user roles are deployed
- C. Only 802.1X authentication is configured on the port
- D. A local user role was deployed using a ClearPass solution
Answer: B
NEW QUESTION 40
How js voice traffic prioritized correctly on AOS-CX switches'?
- A. By implementing voice VLANs
- B. By implementing weighted fair queueing (WFQ)
- C. By defining device profiles with QOS settings
- D. By placing tt in the strict priority queue
Answer: A
NEW QUESTION 41
Examine the following AOS-CX configuration:
Based on this configuration, which statement is correct regarding loT traffic'?
- A. The next hop of 10 100 1.2 can be one or more hops away from the AOS-CX switch.
- B. If 10.100.1.2 is not reachable the loT traffic will be automatically dropped by the switch
- C. All routes are ignored in the routing table for loT traffic, which is routed to 10 100 1 2.
- D. If a specific route is not available in the routing table the traffic will be routed to 10 100 1.2
Answer: B
NEW QUESTION 42
Examine the AOS-CS switch output:
Based on this output, what is correct?
- A. 802.1X authentication was successful, but MAC authentication is yet to start
- B. 802.1X authentication occurred and downloadable user roles are deployed
- C. Only 802.1X authentication is configured on the port
- D. A local user role was deployed using a ClearPass solution
Answer: B
NEW QUESTION 43
What is correct regarding rate limiting and egress queue shaping on AOS-CX switches?
- A. Only a traffic rate and burst size can be defined for a queue
- B. Limits can be defined only for broadcast and multicast traffic
- C. Rate limiting and egress queue shaping can be used to restrict inbound traffic
- D. Rate limiting and egress queue shaping can be applied globally
Answer: B
NEW QUESTION 44
Examine the following AOS-CX configuration:
Based on this configuration, which statement is correct regarding IoT traffic?
- A. If a specific route is not available in the routing table, the traffic will be routed to 10.100.1.2
- B. If 10.100.1.2 is not reachable, the IoT traffic will be automatically dropped by the switch
- C. The next hop of 10.100.1.2 can be one or more hops away from the AOS-CX switch
- D. All routes are ignored in the routing table for IoT traffic, which is routed to 10.100.1.2
Answer: A
NEW QUESTION 45
A network administrator is implementing NAE on AOS-CX switches. When attempting to create an agent on a particular switch, the agent appears in the NAE Agents panel with a red triangle error symbol and a status of
"Unknown".
What is the cause of this issue?
- A. The administrator does not have the appropriate credentials to interact with NAE
- B. The RESTful API has not been enabled on the AOS-CX switch
- C. A connectivity issue exists between NAE and the AOS-CX switch
- D. The number of scripts or agents has exceeded the hardware's capabilities
Answer: C
NEW QUESTION 46
A company requires access by all users guests, and employees to be authenticated Employees will be authenticated using 802 1X. whereas guests will be authenticated using captive portal Which type of authentication must be configured on an AOS-CX switch ports where both guests and employees connect?
- A. Both 802.1X and captive portal
- B. 802 1X only
- C. Both 802 1X and MAC-Auth
- D. 802.1X, captive portal, and MAC-Auth
Answer: C
NEW QUESTION 47
A network has an ABR that connects area 0 and 1. A network engineer configures a summarized route for area 0. The ABR is a designated router (DR) for the segment it uses to connect to area 1.
Which LSA type is assigned to this route when the summarized route is advertised into area 1 by the ABR?
- A. LSA4
- B. LSA3
- C. LSA1
- D. LSA2
Answer: A
NEW QUESTION 48
An administrator is concerned about the security of the control plane connection between an AOS-CX switch and an ArubaMobility Controller (MC) when implementing user-based tunneling How should the administrator protect this traffic?
- A. PAPI with an MD5 pre-shared key
- B. IPSec with a pre-shared key
- C. GRE with a pre-shared Key
- D. IPSec with a digital certificate
Answer: A
NEW QUESTION 49
A company has implemented 802.1X authentication on AOS-CX access switches, where two ClearPass servers are used to implement AAA.
Each switch has the two servers defined. A network engineer notices the following command configured on the AOS-CX switches:
radius-server tracking user-name monitor password plaintext aruba123
What is the purpose of this configuration?
- A. Define the account to implement change of authorization
- B. Implement replay protection for AAA messages
- C. Define the account to implement downloadable user roles
- D. Speed up the AAA authentication process
Answer: A
Explanation:
https://techhub.hpe.com/eginfolib/networking/docs/switches/K-KA-KB/16-01/5200-
0122_access_security_guide/content/ch09s02.html
NEW QUESTION 50
A company requires access by all users, guests, and employees to be authenticated. Employees will be authenticated using 802.1X, whereas guests will be authenticated using captive portal. Which type of authentication must be configured on an AOS-CX switch ports where both guests and employees connect?
- A. 802.1X only
- B. Both 802.1X and captive portal
- C. Both 802.1X and MAC-Auth
- D. 802.1X, captive portal, and MAC-Auth
Answer: C
NEW QUESTION 51
A network administrator is implementing NAE on AOS-CX switches. When attempting to create an agent on a particular switch, the agent appears in the NAE Agents panel with a red triangle error symbol and a status of
"Unknown".
What is the cause of this issue?
- A. The RESTful API has not been enabled on the AOS-CX switch.
- B. The administrator does not have the appropriate credentials to interact with NAE.
- C. A connectivity issue exists between NAE and the AOS-CX switch
- D. The number of scripts or agents has exceeded the hardware's capabilities.
Answer: D
NEW QUESTION 52
A company has recently upgraded their campus switching infrastructure with AOS-CX switches. They have implemented 802.1X authentication on access ports where laptop and IOT devices typically connect. An administrator has noticed that for POE devices, the AOS-CX switch ports are delivering the maximum wattage to the port instead of what the device actually needs.
Concerned about this waste of electricity, what should the administrator implement to solve this problem?
- A. Enable AAA authentication to exempt LLDP and/or CDP information.
- B. Implement a classifier policy with the correct power definitions
- C. Globally enable the QoS trust setting for LLDP and/or CDP,
- D. Create device profiles with the correct power definitions.
Answer: D
NEW QUESTION 53
A company is implementing a new wireless design and needs it to support high availability, even during times of switch system upgrades. The solution will involve Aruba Mobility Controller (MC) and Aruba AP connections requiring POE. Which campus AOS-CX switch solution and virtual switching should the company implement at the campus access layer?
- A. AOS-CX 6400 and VSX
- B. AOS-CX 8325 and VSF
- C. AOS-CX 6300 and VSF
- D. AOS-CX 8400 and VSX
Answer: B
NEW QUESTION 54
Examine the configuration performed on newly deployed AOS-CX switches:
After performing this configuration, the administrator notices that the switch ports always remain in the EAP start state. What should the administrator do to fix this problem?
- A. Enable change of authorization (CoA)
- B. Create and assign a local user role to the ports
- C. Set the ports to client-mode
- D. Define the server group cppm
Answer: A
NEW QUESTION 55
Which concept is implemented using Aruba's dynamic segmentation?
- A. Colorless port
- B. Zero Touch Provisioning
- C. Root of trust
- D. Device fingerprinting
Answer: D
NEW QUESTION 56
What is the correct way of associating a VRF instance to either a VLAN or an interface?
- A. Switch(config)# interface <interface-ID>
Switch(config-if)# vlan access <VLAN-ID> vrf attach <vrf-name> - B. Switch(config)# vlan <VLAN-ID> vrf attach < vrf-name >
- C. Switch(config)# vlan <VLAN-ID> vrf < vrf-name >
- D. Switch(config)# vlan <VLAN-ID>
Switch(config-vlan-<VLAN-ID># vrf attach < vrf-name >
Answer: D
NEW QUESTION 57
Examine the following AOS-CX configuration:
Based on this configuration, which statement is correct regarding IoT traffic?
- A. If a specific route is not available in the routing table, the traffic will be routed to 10.100.1.2
- B. If 10.100.1.2 is not reachable, the IoT traffic will be automatically dropped by the switch
- C. The next hop of 10.100.1.2 can be one or more hops away from the AOS-CX switch
- D. All routes are ignored in the routing table for IoT traffic, which is routed to 10.100.1.2
Answer: A
NEW QUESTION 58
Examine the network exhibit.
A network administrator is implementing OSPF on a VSX pair of aggregation switches: Agg1 and Agg2. VLANs 10 and 20 are connected to layer-2 access switches. Agg-1 and Agg-2 are configured as the default gateway for VLANs 10 and 20, with active gateway enabled.
What is the best practice for configuring OSPF on the aggregation switches and their connection to the Core switch?
- A. Define separate layer-3 VLAN interfaces between the aggregation and core switches. Enable active forwarding for the Layer-3 VLAN.
- B. Define a layer-2 VSX LAG associated with a layer-3 VLAN interface. Enable active gateway for the Layer-3 VLAN.
- C. Define a layer-2 VSX LAG associated with a layer-3 VLAN interface. Enable active forwarding for the Layer-3 VLAN.
- D. Define separate layer-3 VLAN interfaces between the aggregation and core switches. Enable active gateway for the Layer-3 VLAN.
Answer: B
NEW QUESTION 59
A company has implemented 802.1X authentication on AOS-CX access switches, where two ClearPass servers are used to implement AAA. Each switch has the two servers defined. A network engineer notices the following command configured on the AOS-CX switches:
radius-server tracking user-name monitor password plaintext aruba123
What is the purpose of this configuration?
- A. Define the account to implement change of authorization
- B. Implement replay protection for AAA messages
- C. Define the account to implement downloadable user roles
- D. Speed up the AAA authentication process
Answer: A
Explanation:
Explanation
https://techhub.hpe.com/eginfolib/networking/docs/switches/K-KA-KB/16-01/5200-
0122_access_security_guide/content/ch09s02.html
NEW QUESTION 60
An administrator is implementing a multicast solution in a multi-VLAN network. Which statement is true about the configuration of the switches in the network?
- A. IGMP requires join and leave messages to graft and prune multicast streams between switches
- B. IGMP must be enabled on all routed interfaces where multicast traffic will traverse
- C. IGMP must be enabled on all interfaces where multicast sources and receivers are connected
- D. IGMP snooping must be enabled on all interfaces on a switch to intelligently forward traffic
Answer: A
NEW QUESTION 61
Which protocol does NetEdit use to discover devices in a subnet during the discovery process?
- A. LLDP
- B. ICMP
- C. ARP
- D. DHCP
Answer: A
NEW QUESTION 62
......
Aruba Certified Switching Professional (ACSP) V1 Free Certification Exam Material from Actual4Dumps with 102 Questions: https://www.actual4dumps.com/HPE6-A73-study-material.html
HPE6-A73 Dumps Full Questions - Exam Study Guide: https://drive.google.com/open?id=1iFbX1dethFz4quRQMQoVViITKBOUlgLM